林恒勝 教授 兼 智慧機電學院副院長
- 系所：模具工程系
- 研發領域：機械工程
- 標籤： 精微模具
- 專長： 模具設計與分析,金屬成形,磨潤學,IC封裝測試
- 學歷：
美國西北大學機械工程博士
國立臺灣大學機械工程學士
- 經歷：
金屬工業研究發展中心 金屬成形組 工程師1998-2001
- 電話：(07)381-4526#15423
- 傳真：(07)390-7424
1
超微型射頻連接器微成形之各式引伸工法 與板材鍛造增厚改善對策Various micro-forming methods for an ultra-miniatured radio-frequency connector and the strategies to improve plate thickness
2
導線架沖切斷面與殘留應力對烘烤翹曲之影響分析The effect of the punching profile and residual stress of leadframe on the baking warpage
3
板材特性對沖切鼓脹毛刺之影響The effects of plate properties on the formation of bulging burrs in the shearing process
4
伺服沖床之滑塊曲線對彎曲成形之影響分析The Influence of the Slider Curve of Servo-press on Bending
5
沖壓導線架尖角端沖切毛邊之成因與改善對策Causes and countermeasures of stamping lateral burrs at the sharp corners of power lead frames
6
厚板齒輪成形之精密沖切工法分析Analysis of Precision Blanking and Forming Methods for a Thick Plate Gear
7
貨車斗底板之板金成形分析An analysis of sheet metal forming for a truck bed floor
8
沖壓殘留應力對導線架翹曲影響之分析An Analysis of Influence of Residual Stress on the Warpage of Stamped Lead Frames
9
鋁合金薄殼筒件製程之研究The Study Of Manufacturing Process For Thin-wall Shell Part Of The Aluminum Alloy
10
厚板齒輪沖鍛製程之可行性研究Feasibility Study of the Plate Forging Process for a Thick Gear
11
超微型射頻連接器之微成形連續模具設計與板材鍛造改善對策Improvement of the die design for the ultra micro-miniature RF connector with progressive micro forming and plate forging
12
精密沖切法對沖壓導線架翹曲的影響分析The analysis of the effects of precision stamping on the warpage of the lead frame
13
沖壓導線架烘烤翹曲之有限元素分析An FE analysis for the cause of warpage in baking of the stamped leadframe
14
沖鍛彎曲破裂與彎曲回彈之改善方案Strategies in improving the fracture from stamping-forging and the spring-back from bending
15
六角凸緣螺栓搓牙成形之負荷感測研究A study on the load sensing and monitoring in thread rolling of a hexagonal nut
16
扁平引伸壁厚不均之成因與改善對策The cause and improvement for the uneven wall thickness in flat-type drawing
17
六角焊接螺帽成型缺陷之分析與改善Analysis and improvement of forming defects of hexagonal welding nut
18
特殊平頭螺絲成形設計與分析Design and analysis of forming for a special flat head screw
19
伺服沖床之滑塊曲線對彎曲回彈之影響The Influence of the Slider Curve of Servo-press on the Springback in the Bending Processes
20
精密鑄造模擬於薄壁型鑄件製程之應用Investment Casting Simulation for Process Application of Thin Wall Casting
21
等粒徑聚已內酯微載體開發The Development of PCL Micro-carriers with Uniform Diameters
22
板材鍛造背側缺陷之二維分析與解決方案A Two Dimensional Analysis and Solution for The Back Defects in Plate Forging
23
板材鍛造背側缺陷之三維分析與解決方案A three dimensional analysis and solution for the back defects in plate
24
超薄電磁鋼片V型疊層鉚接之沖壓工法分析The Stamping Process and its Analysis of V-shape Stacking for Ultra-thin Electrical Steel Sheets
25
搓牙成形過程之橫向負荷感測監控方法The Method of Transverse Load Sensing and Monitoring in Thread Rolling